NOTE gcode files need to be in a zip format to upload.
- TED BRANDED SNOWMAN 202416.94 MBNovember 18, 2024
A hollow snowman with removable head for stashing stuff or making presents.
- Ender 3 Took Rack for KE156.54 MBJuly 15, 2024
Original tool holder modified for took kit of the KE. PLace for everything that comes with it.
- Ender3 V3 KE alternate bracket for MMI/Tool Rack5.92 MBJuly 15, 2024
This replaces the bracket that holds the display and makes provision for a nameplate and a tool rack.
- Washer Assortment for the Capricorn Fix on the Ender Hot End185.93 KBJune 28, 2024These washers are placed between the small piece of Capricorn PTFE tube and the pneumatic fitting that holds the white PTFE.
- Cone fidget toy20.25 MBApril 19, 2024
From April 19, 2024 meeting. This is two stl files FREE from Cults that is the shaped multi-start threaded cones exemplified at the meeting.
- Look Straight Bear for Michelle30.22 MBApril 19, 2024
The SAM special. Fixed bear that looks straight when the head is tight.
- Bed Leveling routine [gcode]45.69 KBApril 19, 2024
Goes around two times to feeler gage with paper and then prints out pattern. If firmware responds to M0 you can remove the G4 delays
- Mesh Mixer 3rd party manual3.46 MBPreviewMarch 14, 2024To augment our meeting and workflow on Meshmixer
- Ted Head2.04 MBJanuary 5, 2024
For remixing in Bear Head, Totem pole, PEZ dispenser or other creative endeavors.
- Support Tester60.34 KBAugust 19, 2023A 1 inch cube with various overhangs to test types of supports. 30, 45, 60 and 90 degrees plus a hole.
- Dust_cover884.00 bytesMay 3, 2023Handy dandy dust cover for the slots in the rail next to the main board (left side) Print two, takes about 40 minuites
- Poor Man’s Filament Dryer588.00 bytesDecember 8, 2022Code to move extruder out of the way, heat bed to 70C, wait 2 hours, shut down
- Micro SD Car Organizer With Tray58.77 KBSeptember 13, 2022This is a multi micro sd card holder/organizer. Also has a small holding space for other parts or tools. Made to fit Ender 3 but can be modified.
- Totem-Blank drawing179.67 KBPreviewAugust 17, 2022Note is has been 57 years since I was in Mechanical Drawing Class
- Speedy Spool Holder left side231.17 MBMay 10, 2022Quick spin includes rounded threads and slotted shaft
- Ender Speedy Spool Holder Right230.98 MBMay 10, 2022Quick spin includes rounded threads and slotted shaft
- Leveling knob (wheel) detent right side95.79 KBMay 5, 2022Detent cam to keep leveling knobs from coming loose.
- Leveling wheel(knob) detent Left side77.23 KBMay 5, 2022Detent cam to keep leveling knobs from coming loose.
- TED BRANDED SNOWMAN 202416.94 MBNovember 18, 2024
A hollow snowman with removable head for stashing stuff or making presents.
- Ender 3 Took Rack for KE156.54 MBJuly 15, 2024
Original tool holder modified for took kit of the KE. PLace for everything that comes with it.
- Ender3 V3 KE alternate bracket for MMI/Tool Rack5.92 MBJuly 15, 2024
This replaces the bracket that holds the display and makes provision for a nameplate and a tool rack.
- Washer Assortment for the Capricorn Fix on the Ender Hot End185.93 KBJune 28, 2024These washers are placed between the small piece of Capricorn PTFE tube and the pneumatic fitting that holds the white PTFE.
- Cone fidget toy20.25 MBApril 19, 2024
From April 19, 2024 meeting. This is two stl files FREE from Cults that is the shaped multi-start threaded cones exemplified at the meeting.
- Look Straight Bear for Michelle30.22 MBApril 19, 2024
The SAM special. Fixed bear that looks straight when the head is tight.
- Bed Leveling routine [gcode]45.69 KBApril 19, 2024
Goes around two times to feeler gage with paper and then prints out pattern. If firmware responds to M0 you can remove the G4 delays
- Mesh Mixer 3rd party manual3.46 MBPreviewMarch 14, 2024To augment our meeting and workflow on Meshmixer
- Ted Head2.04 MBJanuary 5, 2024
For remixing in Bear Head, Totem pole, PEZ dispenser or other creative endeavors.
- Support Tester60.34 KBAugust 19, 2023A 1 inch cube with various overhangs to test types of supports. 30, 45, 60 and 90 degrees plus a hole.
- Dust_cover884.00 bytesMay 3, 2023Handy dandy dust cover for the slots in the rail next to the main board (left side) Print two, takes about 40 minuites
- Poor Man’s Filament Dryer588.00 bytesDecember 8, 2022Code to move extruder out of the way, heat bed to 70C, wait 2 hours, shut down
- Micro SD Car Organizer With Tray58.77 KBSeptember 13, 2022This is a multi micro sd card holder/organizer. Also has a small holding space for other parts or tools. Made to fit Ender 3 but can be modified.
- Totem-Blank drawing179.67 KBPreviewAugust 17, 2022Note is has been 57 years since I was in Mechanical Drawing Class
- Speedy Spool Holder left side231.17 MBMay 10, 2022Quick spin includes rounded threads and slotted shaft
- Ender Speedy Spool Holder Right230.98 MBMay 10, 2022Quick spin includes rounded threads and slotted shaft
- Leveling knob (wheel) detent right side95.79 KBMay 5, 2022Detent cam to keep leveling knobs from coming loose.
- Leveling wheel(knob) detent Left side77.23 KBMay 5, 2022Detent cam to keep leveling knobs from coming loose.
- Temp Tower for Cura or Other slicers43.13 KBPreviewJanuary 28, 2022You get new filament and rather than making mistakes at what is best temp, you can use this instead. Excellent YouTube Video to explain how to edit the G-Code to change Temp easily on each level as it goes up!
https://www.thingiverse.com/thing:2729076 - *NANO* All In One 3D printer test42.87 KBPreviewJanuary 28, 2022https://www.thingiverse.com/thing:4777912
- CURA Preset for Litho .12 Nozzle829.00 bytesJanuary 28, 2022I printed about 15 Litho Boxes for Christmas. These are the best settings I found & edited to make the best Litho on an Ender 3. I was talking with the Gal today, Sorry I'm bad with names...but she was having some lines she was trying to get rid of...these settings might help!!!
- Z axis spacer for Ender 3 (aligns Z screw)45.79 KBJune 27, 2021This space engages with the 20x40 vertical extrusions and is sandwiched by the 2=axis motor. The notches allow for the mounting screws to pass through. This is standard issue in the BYO class.
- SpaceForce.png81.92 KBPreviewJune 8, 2021As requested at our meeting, SpaceForce.png (as this system didn't like a SpaceForce.gcode file format,(the System Protection is Understood) It,s just a snapshot picture so. Just drop it on CURA and adjust to your tweeking prefs and slice it. Worked for me 🙂
- Wire Guide for pegboard903.21 KBMay 4, 2021I have three battery chargers mounted on my pegboard and needed to route the power cords. I printed (5) to route the cords to the outlet. Print on edge with supports. To mount, I used a small sheetrock screw (becareful not to strip out the pegboard). Bill Hutton 5/4/21
- Dust cover for ender-3884.00 bytesApril 25, 2021You will need two. They fit in the channels on the left side. Bill Hutton 4/25/21