{"id":1586,"date":"2022-12-26T18:29:06","date_gmt":"2022-12-27T00:29:06","guid":{"rendered":"https:\/\/cbimakerspace.com\/E3club\/?p=1586"},"modified":"2023-05-02T08:36:25","modified_gmt":"2023-05-02T14:36:25","slug":"meeting-dec-9th-2022-26","status":"publish","type":"post","link":"https:\/\/cbimakerspace.com\/E3club\/archives\/1586","title":{"rendered":"Meeting Dec 9th, 2022 #26"},"content":{"rendered":"\n

(15) 3D Aficionados: Tom, Bruce, Gil, Charlie, Bernie, Pat, Sam, John H. Bill, Paul, Tom, Ted (Photos), and Mark (virtually via octoeverywhere).<\/p>\n\n\n\n

Topic was: \u201cNEVERENDer\u201d a 3D belt printer or PrintMill, along with Filament Types.<\/p>\n\n\n\n

\n
\"\"
Mark’s Dragon<\/figcaption><\/figure>\n<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n
\"\"<\/figure>\n\n\n\n

I’m printing these at 230\u00b0 bed start temp of 75\u00b0 first layer, 80\u00b0 2nd layer, then 85\u00b0 after layer 21. I’m printing at 45mm\/s with a jerk of 20 starting 2nd layer. <\/p>\n\n\n\n

Retraction is a 5.5 @ 50mm\/s<\/p>\n\n\n\n

Infill 0<\/p>\n\n\n\n

Walls 3<\/p>\n\n\n\n

Bottom initial layers 3<\/p>\n\n\n\n

Bottom layer 4<\/p>\n\n\n\n

Top layer 5<\/p>\n\n\n\n

100% flow except first layer 95%<\/p>\n\n\n\n

.2mm layer after initial .28 layer.<\/p>\n\n\n\n

Travel is set at 150mm\/s but if it wasn’t for all the individual pieces of the Dragon, I get less hair strands at 200mm\/s travel but more chance of shaking a part loose. <\/p>\n\n\n\n

As far as stringing, I don’t get any due to rapid movement. <\/p>\n\n\n\n

My beds don’t have springs either, I have them locked in place.<\/p>\n\n\n\n

Running latest version of mriscoc professional firmware, using 9×9 mesh leveling for Dragon and UBL (Unified Bed Leveling) for every print after that. I haven’t adjusted my beds since October and I’ve made a lot of Dragons since then putting out 2 every 19-20hrs.<\/p>\n\n\n\n

The Chinese Dragon is a Flexi Dragon that is about 2ft 3in long and it sits up. Can me found on Flexi Factory on Cults 3D. <\/p>\n\n\n\n

Pay no attention to the Teflon tubing, I’m running Capricorn in the hotends, but I have 2 heat break tubes I’ll be putting in both printers that are titanium that I can’t Wait for Christmas to be over to test out! <\/p>\n\n\n\n

Cheers <\/p>\n\n\n\n

Mark Leckington <\/p>\n\n\n\n

\n
\"\"
Aficionados<\/strong><\/figcaption><\/figure>\n\n\n\n
\"\"
Bruce Warps<\/figcaption><\/figure>\n\n\n\n
\"\"
Bruce Warps<\/figcaption><\/figure>\n\n\n\n
\"\"
Bill<\/strong><\/figcaption><\/figure>\n\n\n\n
\"\"
Bill<\/strong><\/figcaption><\/figure>\n\n\n\n
\"\"
Bill<\/strong><\/figcaption><\/figure>\n\n\n\n
\"\"
See My Low Cost Heater<\/strong><\/figcaption><\/figure>\n\n\n\n
\"\"
Snowmen are Barred From Building !!!<\/strong><\/figcaption><\/figure>\n\n\n\n
\"\"
Heaters —– Belt Printer<\/strong><\/figcaption><\/figure>\n\n\n\n
\"\"
It’s Pizza Time -)<\/strong><\/figcaption><\/figure>\n<\/figure>\n\n\n\n
<\/figure>\n\n\n\n